carbon brush
英 [ˈkɑːbən brʌʃ]
美 [ˈkɑːrbən brʌʃ]
炭刷
双语例句
- Phase: Touch regulator contains 1 servo motor, 1 phase 1 wrap with decelerate tranmission type to operate carbon brush.
单相：接触式调压器是一台由伺服电机及减速传动机构带动碳刷的单相自藕器。 - Removing all parts of cover, rings, carbon brush, brush box, brush box shell and short circuit ring equipment ( some motor have no short circuit ring equipment).
先拆下电动机的护罩、滑环、碳刷、刷盒、刷盒支架及短路环装置（有的电机无短路环装置）等全部零件。 - You should often clear up carbon brush.
你需要经常清洗炭刷。 - Machinable various types of high-purity graphite-graphite, graphite of mechanical parts and graphite crucible, bearing graphite, carbon brush, and so on.
高纯石墨可加工各类石墨模、石墨质机械零件、石墨坩埚、石墨轴承、碳刷等。可用于冶金、化工、轻工、制药、纺织、石油、国防、航天等行业。 - Talking about fault treatment and daily maintenance of generator carbon brush
浅谈发动机碳刷的故障处理及日常维护 - Based on observation, measurement, and specialists analysis, the main causes of burnout failure for carbon brush on said generators have been found.
根据观察、测量及分析，找出了发电机碳刷烧损事故的主要原因。 - It can maintenance and extend life without carbon brush and gear wheel.
无须碳刷和齿轮，减少维护和大大延长生命。 - When the wear of the carbon brush reaches to the limit, the wear limit alarm device can timely remind the user of replacing the carbon brush, so the non-normal damage of the machine is avoided.
本实用新型在碳刷磨损达到极限时，可以及时提醒用户更换碳刷，避免了机器非正常损坏。 - We supply high quality carbon brush.
提供优质碳刷。 - Reason Analysis and Its Prevention of Carbon Brush Light in Bulb Tubular Turbine Generator
灯泡贯流式机组碳刷火花原因分析与防范措施 - The carbon brush supplies power for the cutting machine to reduce the waste of energy.
切割机的电源由碳刷提供，利于减少能耗。 - Carbon brush test on short circuit commutator
电刷短路换向器试验 - Should guarantee to maintain the contact between the carbon brush and the rolling rings all the time.
应该保证碳刷和滑环始终保持接触。 - The reason for the misoperation of the rotor grounding relay is the unstable touch of the ground carbon brush with the rotor shaft.
分析了接地导纳型继电器运行中因接地碳刷与转子大轴接触不良引起一点接地信号误发的原因。 - The paper describes in detail the method of improving this carbon brush system, comprising modification design, slip-ring surface abrasion treatment, contact bar-carbon brush, and so on.
就浙江省玉溪水电站滑环碳刷系统改进的方法做了详细介绍，包括：碳刷改型设计、滑环表面磨损处理、汇流排和碳刷握的改进。 - Reason analysis and stop of generator excitation carbon brush strike fire
发电机励磁碳刷打火原因分析及消除 - Carbon brush ⅰ and ⅱ using foliate graphite A and B respectively were prepared under the same technological conditions and with modified thermosetting resin as binder.
用改性热固性树脂作粘结剂，分别用A和B两种鳞片石墨作原料，采用相同的工艺条件制得和两种炭刷坯体。 - One Method for Evaluating Service Life of Carbon Brush
电刷使用寿命的评估方法 - Improving slip-ring and carbon brush system for import bulb hydro-generating units
进口灯泡贯流式机组滑环碳刷系统的改进 - Analysis and Prevention of Fever of Carbon Brush and Slip Ring for Generator Excitation and Countermeasures
发电机励磁碳刷滑环发热的分析预防和应急处理措施 - Study on the Preparation Process and Properties of High-Resistance Carbon Brush
高阻炭刷制备工艺和性能的研究 - Develop of No Carbon Brush, No Contact Point, Compensation Type Electric Voltage Stabilizer
一种无碳刷、无触点、补偿式电力稳压器的研制 - Study on Properties of Phenolic Moulding Compound for Carbon Brush Shelf of Automobile
汽车碳刷架用酚醛模塑料的性能研究 - The negative carbon brush damage often occurs in operation.
运行中负极电刷易受损伤。 - The metallographic analysis shows that the microstructure of carbon brush ⅰ which has a streamlined cross section and homogeneous distributed fine pores, is much better than that of carbon brush ⅱ.
从金相分析可以看出，炭刷比炭刷有更好的微观结构，其截面呈流线型，气孔细小、分布均匀。 - It is analyzed that phenomena for the carbon brush of the direct current exciter to strike a light about six generator sets in the Power Plant of Shanxi Aluminium Plant.
主要针对山西铝厂自备热电厂六台发电机组的励磁机碳刷打火现象进行了分析、控制与处理。 - Analysis and Treatment for the Carbon Brush of Direct Current Exciter to Strike a Light on the Spot
现场直流励磁机碳刷打火的分析与处理 - To eliminate the radial pressure imposed on the rotated shaft by the carbon brush and realize good electrical Conductibility, the symmetrical double carbon brush is adopted in the system.
采用对称碳刷设计进行旋转工具电极引电，消除碳刷对旋转轴的径向压力，保证引电可靠； - The carbon brush shelf for automotive start motor and made by this material has passed the measurements in Valeo Co., France.
采用该材料制成的汽车起动电机用碳刷架通过了法国Valeo公司测试。 - Currently, wafer cleaning machine are drived by DC servo motor, but wearing and tearing of the carbon brush has polluted to the dust-free working environment, increasing the cost of maintenance.
目前晶圆清洗机采用直流伺服电动机作为驱动电机，但碳刷的磨损给无尘工作环境带来了污染，增加了维护成本。